Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
- 10. Axes and power shafts
   10.1. Specifications
   10.2. A power shaft
   10.3. A power shaft with SHRUS ball and Birfield type
   10.4. A power shaft with SHRUS Birfield and трипоидного type
   10.5. A rotary fist and a nave of a forward wheel
   10.6. A back axis
   10.7. Search and elimination of malfunctions
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes




10.3. A power shaft with SHRUS ball and Birfield type

1 – cтопорное a ring;
2 – cтопорное a ring;
3 – a protective cover;
4 – a collar;
5 – a collar;
6 – the SHRUS of ball type;
7 – cтопорное a spring ring;
8 – a clip dynamic демпфера;
9 – dynamic демпфер;
10 – a collar;
11 – a collar;
12 – SHRUS Birfield;
13 – a dustproof ring;
14 – a nut, 220–260 Н•м;
15 – a protective cover.

Dismantling

The prevention

Do not assort the SHRUS of type Birfield.
For greasing of SHRUS use only special greasing.
At SHRUS assemblage it is necessary to establish new collars.


PERFORMANCE ORDER
1. Remove collars and pull together a protective cover from a ball SHRUS of a power shaft.

The prevention

Be careful not to damage a protective cover.


2. A screw-driver with a flat edge remove a lock ring.
3. Remove a ball SHRUS from a power shaft.
4. Remove a spring lock ring, take out an internal ring, the case and balls in gathering.
5. Without dismantling clear an internal ring, the case and balls.
6. Remove collars and pull together protective covers of a ball SHRUS and SHRUS Birfield.

The prevention

If the protective cover is repeatedly used before removal of a cover for its protection, wrap up шлицы a power shaft a sticky tape.



Check

PERFORMANCE ORDER
1. Check up a ball SHRUS on absence of traces of a rust, damages of an external ring, an internal ring and balls.
2. Check up a condition шлицов a power shaft.
3. Check up on absence of traces of a rust, water and extraneous subjects in a protective cover of SHRUS Birfield.

The prevention

In SHRUS Birfield it is possible to replace greasing only.



Assemblage

PERFORMANCE ORDER
1. Before installation of a cover for its protection wrap up шлицы a power shaft from the ball hinge a sticky tape.
2. Put greasing on a power shaft and establish a cover.

Greasing of SHRUS Birfield: MS511–50
Greasing of a ball SHRUS: MS511–50

3. For installation dynamic демпфера arrange SHRUS Birfield on a straight line in relation to a shaft, arrange демпфер on distance 301±2 mm and fix its clip.
4. Put greasing on an internal ring and the case. Establish the case so that displacement on a surface качения settled down, as is shown in drawing.

The prevention

Use the greasing delivered together with the repair complete set.


5. Put greasing on the case and the balls located in the case.
6. Establish the hinge, as is shown in drawing, and fix its spring lock ring.
7. Enclose 45±5 г greasings in an external ring and establish it on a power shaft.
8. Enclose 30±10 г greasings in a protective cover and establish a cover on the hinge.

Protective cover of the ball hinge
Greasing total: 75±15 г
The hinge: 45±3 г
Protective cover: 30±10.

9. Fix a protective cover collars.
10. Add in SHRUS Birfield so much greasing, how many it has been wiped during hinge check.
11. Establish covers.
12. Fix a protective cover of SHRUS Birfield collars.
13. Fix covers so that the length of a power shaft corresponded to demanded values.

Length of the left power shaft:
With a mechanical transmission: 626,2±2 mm
With an automatic transmission: 644,9±2 mm
Length of the Right power shaft:
With a mechanical transmission: 933,2±2 mm
With an automatic transmission: 933,9±2 mm